1 X Multicore LMP Solder Tin/lead/Silver 362 Flux 5 Core Solder 1.22mm-500grms

Brand: Multicore

Container Size: 500gms

Solder Type: LMP (Low Melting Point) Sn62/Pb36/Ag2

Solder Form: Wire

Expiry Date: Does Not Apply

MPN: Does Not Apply

Modified Item: No

Wire Diameter: 1.22mm

1 x Roll Multicore Solder LMP Tin/lead/Silver 362 5 Core Flux Solder 1.22mm 500gms, Condition is Brand new.

PRODUCT DESCRIPTION

Sn62-Pb36-Ag2

Low Melting Point solder wire.

Temperature: 181°C - 183°C

LOCTITE 362 provides the following product characteristics:

FEATURES AND BENEFITS

● Good wetting on most common surfaces

● Formulated for general work

● Non-corrosive

● Fast soldering

● Rosin based

● Halide activated

TYPICAL PROPERTIES

ALLOYS:

The alloys used in LOCTITE 362 cored solder wires conform to the purity requirements of the common national and international standards. A wide range of wire diameters is available manufactured to close dimensional tolerances.

FLUX:

LOCTITE 362 solid flux leaves dry and non sticky residues. In use, its odor is typically that of rosin fluxes.

FLUX PROPERTIES

DIRECTIONS FOR USE

Soldering Iron:

Good results should be obtained using a range of tip temperatures. However, the optimum tip temperature and heat capacity required for a hand soldering process is a function of both soldering iron design and the nature of the task and care should be exercised to avoid unnecessarily high tip temperatures for excessive times. A high tip temperature will increase any tendency to flux spitting and it may produce some residue darkening.

The soldering iron tip should be properly tinned and this may be achieved using LOCTITE cored wire. Severely contaminated soldering iron tips should first be cleaned and pre-tinned using Multicore Tip Tinner/Cleaner, then wiped on a clean, damp sponge before re-tinning with LOCTITE cored wire.

Soldering Process:

LOCTITE 362

March-2016

● Apply the soldering iron tip to the work surface, ensuring that it simultaneously contacts the base material and the component termination to heat both surfaces adequately. This process should only take a fraction of a second.

● Apply LOCTITE flux cored solder wire to a part of the joint surface away from the soldering iron and allow to flow sufficiently to form a sound joint fillet. This should be virtually instantaneous. Do not apply excessive solder or heat to the joint as this may result in dull, gritty fillets and excessive or darkened flux residues.

● Remove solder wire from the work piece and then remove the iron tip.

The total process will be very rapid, depending upon thermal mass, tip temperature and configuration and the solderability of the surfaces to be joined.

LOCTITE flux cored solder wires provide fast soldering on copper and brass surfaces as well as solder coated materials. Activity of the halide activated versions on nickel is also good depending on the state of oxidation of the nickel finish. The good thermal stability of Multicore fluxes means they are also well suited to soldering applications requiring high melting temperature alloys.

Cleaning:

LOCTITE 362 cored solder wires have been formulated to leave pale flux residues and to resist spilling and fuming.

Cleaning will not be required in most situations but if necessary this is best achieved using LOCTITE MCF 800 Cleaner (see separate technical data sheet). Other proprietary solvent or semi-aqueous processes may be suitable. Saponification may be viable but customers must ensure that the desired level of cleanliness can be achieved by their chosen system.

Surface Insulation Resistance

LOCTITE 362 flux pass the J-STD-004 SIR test and other elements of J-STD-004 test protocols associated with flux classification ROL1.

Electromigration

LOCTITE 362 passes the Bellcore GR-78-CORE Electromigration test.

DATA RANGES

The data contained herein may be reported as a typical value and/or a range. Values are based on actual test data and are verified on a periodic basis.

GENERAL INFORMATION

For safe handling information on this product, consult the Material Safety Data Sheet (MSDS).

Not for Product Specifications

The technical information contained herein is intended for reference only. Please contact Henkel Technologies Technical Service for assistance and recommendations on specifications for this product.

Technical Data Sheet

Technology Solid flux

Application Solder flux

Acid Value, mg KOH/g 170

Halide Content, % <0.5

SIR Test (without cleaning), J-STD-004 PASS

J-STD-004 classification ROL1

EN29451-1 classification 1.1.2

LOCTITE cored wires contain a

activators to provide clear residues, maximum activity and high residue reliability, without cleaning in most situations. To achieve the best results from LOCTITE solder wires, recommended working practices for hand soldering should be observed as follows